INNOVATIVE PRODUCTS
LOAD MONITORING
SSR Mounted, Heater, SSR and Power Monitor Low Cost Heater / Loop Break Alarm
The SSRMON is designed for monitoring the condition of an SSR (solid state relay) and its load circuit. The SSRMON mounts directly on top of any standard SSR via the connection terminals and monitors the drive and output to detect open heater /load, loss of line and DC power, shorted SSR, etc. The SSRMON provides a bright green normally illuminated LED as well as a versatile normally closed relay output which can be easily integrated into your control system or connecting to your PLC. The SSRMON operates from 12 or 24 VDC power and can be used for detection in 100 to 660VAC applications. The SSRMON is about the simplest lowest cost heater break alarm solution available.
True RMS Current Controller
The NWCC is a closed loop current controller that provides PID control of a phase angle driven load circuit. The True RMS current is sensed by an on board isolated current transducer. The current setpoint is set by an external command signal or the on board potentiometer. The current command input accepts 0-5V, 0-10V, 4-20mA, Potentiometer, etc. The major advantage to the NWCC is that it can accurately sense and quickly control the True RMS current of phase controlled loads. This regulates the load current, limits inrush and current demand under load changes. The NWCC is designed to be used in conjunction with the NuWave SSRMAN-1P series phase controls or with any phase control.
True RMS Current Transformer
The NWCT is a current transformer/transducer that provides a 0-10V or 4-20mA output that is proportional to the current signal present on the conductor passed through the onboard sense transformer. The major advantage to the NWCT is that it can accurately sense nonlinear and distorted sinusoidal signals such as phase controlled loads and provide a True RMS conversion of the signal. Less sophisticated current transformer units suffer from severely inaccurate conversion of these types of signals. This is because they tend to respond only to the instantaneous peaks of the signal which have nothing to do with the actual current present in the load circuit. The NWCT is a major improvement over these designs, offering greater accuracy, stability and flexibility.
Wire Lead Current Transformer P/N CR8450-1000
The new CR8400 series of wire lead transformers provides a high quality solution, at low cost for current sensing. Major applications include ground fault relays, current measurements, power monitoring and over/under current sensing. This series of transformers provides the benefit of a high accuracy remote monitor for cost sensitive projects. They are epoxy encapsulated to provide protection from the environment. Electrical insulation is rated at 100M ohm @ 500 Vdc. Detailed information is available for operation in 50 to 400 Hz systems. The CR8400 series of current transformers are constructed using core material of a high grade laminated nickel alloy or silicon steel material. The styles have window opening sizes of .232" to .610" diameter with .709", to 1.181" O.D.
POWER CONTROL
| SOLID STATE RELAY CONTROL MODULES | Download Brochure |  |
|---|
Microprocessor Controlled SSR Mount Phase Angle Control Module
Featuring soft start, line voltage compensation & much more
The microprocessor based SSRMAN-1P phase angle control module is designed for use in a broad range of power control applications using a solid state relay. The SSRMAN-1P mounts directly on the input terminals of an SSR and converts it into a low cost phase angle controller by providing true linear power control of the load via the SSR's logic input. Using the SSRMAN-1P with the appropriate SSR for your load will provide a modular feature packed high isolation SCR power control at a very low price.
SSR Mounted Phase Angle Control Module with Current Limit
True linear power output phase angle control
The microprocessor based SSRMAN-1P-CL mounts directly on the input terminals of an SSR and provides true linear power phase angle control of the load. The output power is based on the command input and the current feedback from the current transformer. The command can be dip switch selected from over seven different industry standard inputs. Using the SSRMAN-1P-CL with the appropriate SSR for your load will provide a modular feature packed high isolation SCR power control at a very low price.
Microprocessor Controlled SSR Mounted Burst Firing (Time Proportioning Control) Module
The SSRMAN-1B's output power is proportional to the command input which can be selected from eight different industry standard inputs. User configurable features such as Power Limit make the SSRMAN-1B a perfect fit for any power control application. Power Limit is set via a potentiometer and will limit the voltage on your load by limiting the duty cycle allowed on the output. The SSRMAN-1B can be used with random fire or zero cross fired solid state relays.
Fast Synchronous Burst Firing Module
The SSRMAN-1BFS is a zero cross burst firing control module designed for use with standard footprint random fire SSRs (Solid State Relays). The module mounts directly on the SSR's input screws and provides 0-100% fast synchronous zero cross burst firing (time proportioning) based on the input signal. The module operates by varying duty cycle of SSR's control input synchronous to the AC line. The power delivered to the load is proportional to the command input signal. The SSRMAN-1BFS can be dipswitch configured for up to six different industry command signals and four different cycle times.
SSR Mounted Current to Time Proportioning Converter
4-20mA Loop Powered Burst Firing with Zero and Span pots and LED
The SSRMAN-1LP burst firing module is deigned for use in a broad range of power control applications where an external power supply is not available. The SSRMAN-1LP mounts directly on the input connections of an SSR and provides precise 0-100% time proportioned drive based on the input signal. The SSRMAN-1LP loop powered burst firing module converts a 4 to 20mA output signal from a process or temperature controller or computer to a time proportioned pulse drive to an SSR thereby controlling the average power to your load (typically electric heaters).
SSR Mounted Temperature Controller
The microprocessor based SSRTC mounts directly on the input terminals of an SSR and provides a low cost temperature control solution. Temperature sensing is accomplished using a thermistor available in many different termination options.
Universal Power Control Module Phase Angle Version
The NWUPCM-1P is a phase angle control module designed for use with Solid State Relays or high power back to back SCR modules. The power delivered to the load is proportional to the command input signal.
Universal Power Control Module Burst Firing Version
The NWUPCM-1B is a burst fire control module designed for use with Solid State Relays or high power back to back SCR modules. The power delivered to the load is proportional to the command input signal.
Inductive Load Power Control Module Phase Angle SCR Driver
The microprocessor based NWIPCM-1P provides true linear phase angle of SCRs for resistive and inductive loads. The output power is proportional to the command input which can be dip switch selected from six different industry standard inputs. The high current gate drive is suitable for large SCRs.
SCR Gate Driver Board - Zero Cross Fired
The NWZC-SCR is suitable for driving back to back SCRs in single or polyphase resistive load applications. The NWZC-SCR in combination with back to back SCRs produces and economical high current solid state relay.
H-BRIDGE CONTROLLERS
Thermoelectrec (TEC) H-Bridge Amplifier
The TCH1560 TEC Amplifier provides a cost effective solution for interfacing a standard heat/cool temperature controller to a Thermo Electric Module (peltier module). The heat and cool inputs are used to control the high current, wide voltage range H-bridge output.
STAGING CONTROL
Low Voltage Step Control With Vernier Stage
The NWVS is a microcontroller-based step controller that provides precise modulation in multi-stage heater applications such as duct heaters. The built-in Vernier stage allows for smooth, precision control of the load without increasing switching wear in the system contactors.
TEMPERATURE AND PROCESS CONTROLLERS
Super Low Cost Single Zone Fixed Setpoint Temperature Controllers
Single Zone Low Cost OEM Temperature Controller
The NWTC-1 is the lowest cost temperature controller in our catalog. It is designed for high volume fixed setpoint applications. The NWTC-1 is factory set for your setpoint and hysteresis but can be adjusted slightly in the field. The NWTC-1 provides an SSR drive output, accepts either thermocouple or RTD and operates from 24VAC/DC power. Minimum orders of 100 pieces apply to waive the setup charges for your temperature range and sensor.
Series 8000 Multizone Temperature Controller
8 Zone, Heat/Cool, Digital Display Temperature Controllers with Serial Communications
CAL 3200 Series 1/32 Din Panel Mount Temperature Controller
The model 3200 was the worlds first 1/32nd DIN (24mm x 48mm) temperature controller launched in 1992. The model is still in full production today.
For the very latest 1/32nd DIN controller, go to the 3300 which uses the same program menus but has the benefit of communications and latest aesthetic designs.
CAL 3300, 9300 and 9400 Series Panel Mount Temperature Controllers
1/32nd and 1/16th Din, Heat/Cool, Digital Display Temperature Controllers with Serial Communications
1/16th Din Digital Display Process Controllers with Serial Communications
CAL 9500 Series Ramp Soak Panel Mount Temperature Controller
Bench Top Heat/Cool Temperature Controller System
Perfect for Laboratory Applications
Single Zone Low Cost OEM Temperature Controller With Integral Sensor
The Micro TC is the smallest and lowest cost temperature controller in our catalog. The Micro TC is factory set for your setpoints and hysteresis but can be adjusted in the field using the 0-5V input or a potentiometer.
TEMPERATURE SENSORS
Quality, Price Competitive Thermocouple probe assemblies, custom tailored to your exact requirements.
Single Zone Low Cost OEM Temperature Controller With Integral Sensor
The Micro TC is the smallest and lowest cost temperature controller in our catalog. The Micro TC is factory set for your setpoints and hysteresis but can be adjusted in the field using the 0-5V input or a potentiometer.
CUSTOM SOLUTIONS
CUSTOM ELECTRONIC PRODUCT DESIGN, SOFTWARE AND PCB DESIGN
Didn't find exactly what you're looking for? Consider a quality custom product designed exactly to your specifications.
NuWave Technologies has the capability to tackle even the most challenging custom designs. We offer concept to completion electronic product development and manufacturing.
Specialists in: low cost designs, custom temperature controls, handheld and battery powered devices, wireless interfaces, USB interfaces, SCR power controls, process control and instrumentation.
NuWave Technologies has been in the business of electronics design and manufacturing since 1996. Our Norristown, Pennsylvania location has facilities for electronics R&D, design, testing, calibration, and manufacturing. The NuWave R&D team has over 50 man-years of experience with many highly skilled contractors available for product development and manufacturing. Our Norristown laboratory has extensive facilities with the latest in high quality test and analytical equipment.
Bench Top Heat/Cool Temperature Controller System
Perfect for Laboratory Applications
ACCESSORIES
SOLID STATE RELAYS| Please contact us for a quotation of your SSR and Heatsink requirents. |  |
|---|
CONTROL TRANSFORMERS
 |
Control transformers for use with NWUPCM-1P/B, SSRMAN-1P/B/BFS, NWCT, NWCC, NWTC-1. |
|---|
 |
For sales and distribution please call 866-379-3597 |
|---|
